Search found 882 matches

by Robert Luland
Wed May 08, 2019 8:58 pm
Forum: Panhead
Topic: Transmission - Shifting into Neutral or First Gear
Replies: 22
Views: 743

Re: Transmission - Shifting into Neutral or First Gear

Steve, did this box ever work properly or was this the way ya got it? Sounds like someone put it together with out a shifter fork alignment tool.
by Robert Luland
Wed May 08, 2019 8:53 pm
Forum: Panhead
Topic: Panhead swingarm frame tabs for
Replies: 6
Views: 318

Re: Panhead swingarm frame tabs for

The top one is for the throttle cable. The lower one left side is for the hydraulic brake line tee. The one on the right side is for the squish pipe. Bob L
by Robert Luland
Sun May 05, 2019 8:52 pm
Forum: Panhead
Topic: Crappy Welding Heads
Replies: 7
Views: 746

Re: Crappy Welding Heads

Boil those suckers in heavy dishwashing liquid mixture. I do this to parts I'm going to parkerize. Just because it looks good coming out of the glass beader, doesn't mean it's clean. Boil them and you won't believe what comes to the top of that lobster pot. Bob L
by Robert Luland
Wed May 01, 2019 12:37 am
Forum: Panhead
Topic: Transmission
Replies: 0
Views: 128

Transmission

While beanie and I were at Oley this weekend. I spotted something I had written about a couple of years before. There was a guy selling a bunch of crap that had come out of Dixie. The product at hand is the one piece kicker arm. They are dirt cheap and defective. If you look at the end the gear goes...
by Robert Luland
Thu Apr 04, 2019 10:46 pm
Forum: Panhead
Topic: Crappy Welding Heads
Replies: 7
Views: 746

Re: Crappy Welding Heads

Are you welding these ports on the outside?
by Robert Luland
Tue Dec 25, 2018 2:39 am
Forum: Panhead
Topic: Crossover shaft too short, locking up.
Replies: 3
Views: 370

Re: Crossover shaft too short, locking up.

Half a dozen oem ones on e-bay. No reason to buy that crap.
by Robert Luland
Sun Sep 30, 2018 1:57 pm
Forum: Panhead
Topic: 68543-61A 6 volt, 2 terminal turn signal flasher
Replies: 11
Views: 1101

Re: 68543-61A 6 volt, 2 terminal turn signal flasher

Just a spring metal base that was attached that the flasher unit slipped into. No different than the rectangular that were pop riveted to the rear fender of most bikes in the 70s.
by Robert Luland
Mon Aug 13, 2018 11:13 pm
Forum: Panhead
Topic: Removing Main Drive Gear Bushing
Replies: 12
Views: 796

Re: Removing Main Drive Gear Bushing

The lines at the end go outward toward the seal.
by Robert Luland
Sat Aug 11, 2018 7:18 pm
Forum: Panhead
Topic: Removing Main Drive Gear Bushing
Replies: 12
Views: 796

Re: Removing Main Drive Gear Bushing

Andy I don't know how far along your are but there is a special Kent-Morse tool to remove and install that I will lend to you if ya haven't finished already. Another thing to look out for guys is the type of bushing on the market. The split one which is just like the original Clevis bushing and the ...
by Robert Luland
Tue Aug 07, 2018 7:09 pm
Forum: Panhead
Topic: Eliminator carb
Replies: 16
Views: 1873

Re: Eliminator carb

That screw came in today and we put it up on the site. Bob L
by Robert Luland
Sun Aug 05, 2018 12:25 am
Forum: Panhead
Topic: Can I use 35065-65B Main Drive gear in a 1952 transmission?
Replies: 2
Views: 303

Re: Can I use 35065-65B Main Drive gear in a 1952 transmission?

Yes it will. The only difference is that the end is machined for the seal and the bushing is shorter. Your not going to find an older one. I'm partial to the Andrews gear. Comes with the bushing pre installed. Bob L
by Robert Luland
Sun Aug 05, 2018 12:08 am
Forum: Panhead
Topic: Eliminator carb
Replies: 16
Views: 1873

Re: Eliminator carb

Have no fear! I ran out of that screw but have more on order. Should be in in under a couple of weeks in I will post them on my site. Bob L
by Robert Luland
Thu May 03, 2018 12:42 am
Forum: Panhead
Topic: V-Twin After Market Rockers
Replies: 11
Views: 1179

Re: V-Twin After Market Rockers

There's only one rice gobbling manufacture that makes those rockers and everybody puts there name on them. They are total shit. The top cover is not bronze like the original but decorative yellow brass because China dosn't have bronze. They produce it but want the O Yankee dollar for it. As in nobod...
by Robert Luland
Wed Apr 18, 2018 1:50 am
Forum: Panhead
Topic: galvanizing recomendations
Replies: 6
Views: 572

Re: galvanizing recomendations

Just do Google search for cadmium platting in your area. I find it hard to believe you can't find a shop in the heart land. Bob L
by Robert Luland
Tue Feb 27, 2018 11:45 pm
Forum: Panhead
Topic: 1950 PAN Bolts
Replies: 2
Views: 386

Re: 1950 PAN Bolts

So does every factory parts book.

Go to advanced search