Search found 1746 matches

by Panacea
Thu May 16, 2019 5:41 pm
Forum: Panhead
Topic: Clutch pushrod questions
Replies: 12
Views: 311

Re: Clutch pushrod questions

The new one looks like it will seal better on the clutch end! Hopefully they replaced the hub nut oil seal...
by Panacea
Thu May 16, 2019 5:34 pm
Forum: Projects
Topic: 65a generator gets a new life!
Replies: 3
Views: 139

Re: 65a generator gets a new life!

If anyone would like to take a Taiwanian armature off my hands , it's yours for the shipping cost. It's the 61 type...Mike
by Panacea
Sun May 05, 2019 1:20 am
Forum: Panhead
Topic: Kicker Arm
Replies: 17
Views: 526

Re: Kicker Arm

That is "the old lesson" check the last thing you worked on...and carry the same tools you used in the tool roll:}
by Panacea
Thu May 02, 2019 3:03 pm
Forum: Panhead
Topic: Kicker Arm
Replies: 17
Views: 526

Re: Kicker Arm

I wonder if the guy that took out the plate over tightened the pushrod. Could be something messed up in the kicker, I would have to remove the kicker cover for an inspection...
by Panacea
Wed May 01, 2019 8:27 pm
Forum: Panhead
Topic: Kicker Arm
Replies: 17
Views: 526

Re: Kicker Arm

Do a simple test to see if the motor turns over when you kick. Take the cover off of the timer, watch for it to rotate...
by Panacea
Mon Apr 29, 2019 7:11 pm
Forum: Panhead
Topic: Transmission Oil Seal
Replies: 8
Views: 459

Re: Transmission Oil Seal

Sorry George, it's gone, but if your main drive gear fits the mainshaft correctly, and you don't over fill your tranny, it won't leak:)
by Panacea
Mon Apr 29, 2019 6:20 pm
Forum: Panhead
Topic: Rear axle spacer stuck to axle: how hot, any tricks?
Replies: 12
Views: 392

Re: Rear axle spacer stuck to axle: how hot, any tricks?

Does the spacer have a little flair where it rests against the frame?
by Panacea
Sun Apr 28, 2019 11:16 pm
Forum: Panhead
Topic: Rear axle spacer stuck to axle: how hot, any tricks?
Replies: 12
Views: 392

Re: Rear axle spacer stuck to axle: how hot, any tricks?

Have a buddy hold a sledge right next to the hex against the frame. put the nut back on the other end of the axle leaving a gap so you can put a block of hardwood over the nut and smack it with a heavy hammer. The sledge will keep the frame from bouncing on the other end...
by Panacea
Sun Apr 28, 2019 11:06 pm
Forum: Panhead
Topic: Transmission Oil Seal
Replies: 8
Views: 459

Re: Transmission Oil Seal

I have one of the spacers with the O-rings if you want it....Mike
by Panacea
Sun Apr 28, 2019 11:04 pm
Forum: Gear Case / Cams
Topic: Cam recommendations
Replies: 8
Views: 2297

Re: Cam recommendations

The original poster may have lost interest after 11 years BM....
by Panacea
Sun Apr 14, 2019 5:37 am
Forum: Panhead
Topic: Rear chain large difference between tight and loose spot
Replies: 6
Views: 229

Re: Rear chain large difference between tight and loose spot

Grab the chain at the rear of the sprocket and see how much you can pull it off of the teeth, if you can see thru the teeth under the chain, it's shot. 3/4" difference between the tightest spot and loosest spot would be normal from my experience, It would be a good idea to check the sprocket when yo...
by Panacea
Mon Apr 08, 2019 1:16 pm
Forum: Panhead
Topic: My 53 panhead
Replies: 16
Views: 650

Re: My 53 panhead

I had the same seepage on three different panheads, no big deal...
by Panacea
Mon Apr 08, 2019 1:13 pm
Forum: Panhead
Topic: 49'Pan, Mousetrap question
Replies: 16
Views: 539

Re: 49'Pan, Mousetrap question

Sounds like a real workout for the wrist. Trying to imagine shifting thru the gears with a left twist grip clutch, So you would have to take your hand off the throttle to grab the right side tank shifter? Perhaps a foot shift setup would be more realistic...
by Panacea
Mon Apr 08, 2019 2:32 am
Forum: Panhead
Topic: oil flow through a 58 motor
Replies: 22
Views: 666

Re: oil flow through a 58 motor

Could the pump gears be to worn to push oil that high? good clear line to the pump?
by Panacea
Sat Apr 06, 2019 4:07 am
Forum: Panhead
Topic: oil flow through a 58 motor
Replies: 22
Views: 666

Re: oil flow through a 58 motor

I used a set of aftermarket inserts when I replaced the chrome blocks for some originals on my 64, I wound up puting the original inserts back in because the new ones wouldn't pump up, total garbage...

Go to advanced search