58R police generator parts

Post Reply
PanPal
Posts: 1148
Joined: Wed Apr 21, 2004 8:57 pm
Bikes: 50 EL custom
58 FL
76 FLH All Original
Location: Maryland

58R police generator parts

#1

Post by PanPal » Fri Nov 17, 2017 10:42 pm

I need of the part on the right in both pictures. Might be the part on the left in the second picture, but I think either would work.
generator parts.jpg
ventelated cover police gen.jpg
You do not have the required permissions to view the files attached to this post.



cdndewey
Posts: 403
Joined: Thu Feb 21, 2008 9:07 am
Bikes: 42 WLC, 47 EL, 53 FLE, 62 FL, 78 FLH
Location: British Columbia

Re: 58R police generator parts

#2

Post by cdndewey » Sat Nov 18, 2017 4:06 pm

PanPal wrote:
Fri Nov 17, 2017 10:42 pm
I need of the part on the right in both pictures. Might be the part on the left in the second picture, but I think either would work.

ventelated cover police gen.jpg
I have one on my generator like the one on the left. I thought some previous owner had done that to it.

PanPal
Posts: 1148
Joined: Wed Apr 21, 2004 8:57 pm
Bikes: 50 EL custom
58 FL
76 FLH All Original
Location: Maryland

Re: 58R police generator parts

#3

Post by PanPal » Thu May 10, 2018 5:57 pm

Does anyone know what size thread the 58R generator armature shaft is? part # 4 in the diagram below. There is a bit of wear on the thread on the shaft and the nut. I would like to clean these up a bit. Just a few little details and this generator will be ready to test. Also would anyone know what the Harley part number is for the fan baffle plate is? Item # 10....
58R gen.jpg
58R part list.bmp
You do not have the required permissions to view the files attached to this post.

hydra74
Moderator and Panhead Register Member
Posts: 706
Joined: Mon Apr 03, 2006 12:50 pm
Bikes: 1943 WLC,1955 FL

Re: 58R police generator parts

#4

Post by hydra74 » Thu May 10, 2018 9:46 pm

according to my parts book the PN for the baffle plate is 30061-49
and # 4 in the diagram is PN 7634 Nut,10-32 x 1/8" x 5/16" hex (brass)

Hydra74

PanPal
Posts: 1148
Joined: Wed Apr 21, 2004 8:57 pm
Bikes: 50 EL custom
58 FL
76 FLH All Original
Location: Maryland

Re: 58R police generator parts

#5

Post by PanPal » Thu May 10, 2018 9:54 pm

Thanks Hydra. I don't think that's right on the nut size though. The best I could measure was .355 OD on the threads on the shaft. Could have been 3/8" but now worn down, but Harley also used some odd thread sizes too. The nut appears to be nice steel and appears to be like other OEM hardware they supplied.

hydra74
Moderator and Panhead Register Member
Posts: 706
Joined: Mon Apr 03, 2006 12:50 pm
Bikes: 1943 WLC,1955 FL

Re: 58R police generator parts

#6

Post by hydra74 » Thu May 10, 2018 10:15 pm

you are right the armature shaft washers # 5 and 6 are both 3/8 so the nut should be the same probably a mistake in my parts book

Hydra74

Post Reply

Return to “Parts Wanted”