Replacing tappets 1940 ULH

Standard tappet size

All flathead topics
Holtvintage
Site sponsor
Site sponsor
Posts: 242
Joined: Sat Aug 19, 2017 12:52 pm
Bikes: 1951 servi, 82 FLH, 2011 FLHR,
Has thanked: 2 times
Been thanked: 8 times

Re: Replacing tappets 1940 ULH

#16

Post by Holtvintage » Thu Feb 07, 2019 5:21 pm

pan620 wrote:
Thu Feb 07, 2019 2:49 pm
Why hone before you buy tappets, if they do not clean up perfect still will be better than what you have? If you would want me to fit oversize tappets I need the ones you are going to use, not some measurement of what someone says they are!
I can understand that. I agree part in hand is always better than "suppose to be" dimensions



Holtvintage
Site sponsor
Site sponsor
Posts: 242
Joined: Sat Aug 19, 2017 12:52 pm
Bikes: 1951 servi, 82 FLH, 2011 FLHR,
Has thanked: 2 times
Been thanked: 8 times

Re: Replacing tappets 1940 ULH

#17

Post by Holtvintage » Fri Feb 08, 2019 4:18 pm

20190208_090527_resized.jpg
20190208_091143_resized.jpg
.7308
You do not have the required permissions to view the files attached to this post.

Holtvintage
Site sponsor
Site sponsor
Posts: 242
Joined: Sat Aug 19, 2017 12:52 pm
Bikes: 1951 servi, 82 FLH, 2011 FLHR,
Has thanked: 2 times
Been thanked: 8 times

Re: Replacing tappets 1940 ULH

#18

Post by Holtvintage » Sat Oct 12, 2019 8:20 pm

I bought some .005 oversized tappets from Eastern the other day. When I checked with the micrometer I found that several were .7350 to .7355 in diameter. Is this typical? I thought that they should be a little more symmetrical. I have 1 that is within .0002 so I know its possible. Am i being too picky? The hone to fit dimension is only .001

Buddhahoodvatoloco
Site sponsor
Site sponsor
Posts: 1315
Joined: Wed Sep 07, 2016 7:13 pm
Bikes: 1969 FLF
1937 EL Sold
1949 rat bike Sold
1946 FL Sold
1940 U
1937 EL
Location: san diego
Has thanked: 441 times
Been thanked: 66 times

Re: Replacing tappets 1940 ULH

#19

Post by Buddhahoodvatoloco » Sat Oct 12, 2019 10:02 pm

Know where they come from, country of origin. :roll:
Holtvintage wrote:
Sat Oct 12, 2019 8:20 pm
I bought some .005 oversized tappets from Eastern the other day. When I checked with the micrometer I found that several were .7350 to .7355 in diameter. Is this typical? I thought that they should be a little more symmetrical. I have 1 that is within .0002 so I know its possible. Am i being too picky? The hone to fit dimension is only .001

38ulh
Posts: 33
Joined: Sat Jul 23, 2011 7:43 pm
Bikes: 05 bonneville 79 flh 38ul 69 trail 90
Location: Nevada
Been thanked: 1 time

Re: Replacing tappets 1940 ULH

#20

Post by 38ulh » Sun Oct 13, 2019 12:33 am

Someone on this GREAT board once replied to my Ul lifter dilema. They informed me that ironhead sportster lifters are the same dimensions as flathead lifters. They were right. I found some NOS on ebay. They came without adjuster screws. I think there are two different thread pitches for the adjusters. I was informed by a knowledgeable member of this board that the holes in flathead lifters have nothing to do with oiling. Ironhead lifters are easily available and they work fine in a flathead engine. But I also have Eastern products in my engine with no issues.

kitabel
Posts: 985
Joined: Tue Aug 03, 2010 7:10 pm
Bikes: 2008 96" Fat Boy TC
Location: Lynbrook, New York
Been thanked: 122 times
Contact:

Re: Replacing tappets 1940 ULH

#21

Post by kitabel » Sun Oct 13, 2019 2:03 am

All 1929-83 tappets are .731" diameter with .855" wheels.
AFAIK all of the adjusters interchange, flat hex, ball cup etc.
The lengths vary a lot, XL is very short, knuck the opposite. If it's too tall you won't be able to install them.
The tappet blocks are part of the oil system (holes vent through the crankcase wall), not the tappets.

Holtvintage
Site sponsor
Site sponsor
Posts: 242
Joined: Sat Aug 19, 2017 12:52 pm
Bikes: 1951 servi, 82 FLH, 2011 FLHR,
Has thanked: 2 times
Been thanked: 8 times

Re: Replacing tappets 1940 ULH

#22

Post by Holtvintage » Sun Oct 13, 2019 4:31 am

Buddhahoodvatoloco wrote:
Sat Oct 12, 2019 10:02 pm
Know where they come from, country of origin. :roll:
Holtvintage wrote:
Sat Oct 12, 2019 8:20 pm
I bought some .005 oversized tappets from Eastern the other day. When I checked with the micrometer I found that several were .7350 to .7355 in diameter. Is this typical? I thought that they should be a little more symmetrical. I have 1 that is within .0002 so I know its possible. Am i being too picky? The hone to fit dimension is only .001
Eastern Brand The package said USA

Holtvintage
Site sponsor
Site sponsor
Posts: 242
Joined: Sat Aug 19, 2017 12:52 pm
Bikes: 1951 servi, 82 FLH, 2011 FLHR,
Has thanked: 2 times
Been thanked: 8 times

Re: Replacing tappets 1940 ULH

#23

Post by Holtvintage » Sun Oct 13, 2019 5:00 am

JIMS part number 2427-1 tappets are replacements for k model 45" and BTSV

Holtvintage
Site sponsor
Site sponsor
Posts: 242
Joined: Sat Aug 19, 2017 12:52 pm
Bikes: 1951 servi, 82 FLH, 2011 FLHR,
Has thanked: 2 times
Been thanked: 8 times

Re: Replacing tappets 1940 ULH

#24

Post by Holtvintage » Sun Oct 13, 2019 5:01 am

tempFileForShare_20191011-101057.jpg
You do not have the required permissions to view the files attached to this post.

Post Reply

Return to “Flathead and Servicar”