Panhead Rear disc brake

All Panhead related topics
Post Reply
DaCs
Posts: 93
Joined: Wed Sep 12, 2018 9:07 pm
Bikes: Panhead FL 1960
Location: Spain
Has thanked: 1 time
Been thanked: 2 times

Panhead Rear disc brake

#1

Post by DaCs » Sun Nov 10, 2019 3:36 am

Hi, Im trying to use the v-twin 22-0403 kit with a GMA 10" Caliper, anybody use it ? what is your opinion? Im dont find any information about the brake line I need, any help? Regards

Image
Image
Last edited by panhead on Sun Nov 10, 2019 11:13 am, edited 1 time in total.
Reason: made pictures visible



RooDog
Site sponsor
Site sponsor
Posts: 954
Joined: Tue Oct 31, 2017 1:00 pm
Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Custom Built Evo 100" Bagger
Location: Knoxville, Tennessee
Has thanked: 217 times
Been thanked: 282 times

Re: Panhead Rear disc brake

#2

Post by RooDog » Sun Nov 10, 2019 4:38 am

You will have to fabricate your own brake line. Use a flex line from the caliper to a T fitting with a hydraulic stop light switch nerr the rear of the transmission and then a hard line forward to the master cylinder. I have used universal hard line from an automotive parts store and bend it as needed. I run it inboard of the frame being sure to keep it above the bottom of the frame, the scrub line, so as not to drag when up on a lift, or when riding over road surface obstructions, like curbs or speed bumps. Also be sure to allow about 1/2", 13 mm, clearance around the exhaust.
The MC pictured has a 3/4" bore, the GMA 5/8" MC works a little better and is what I use. The iron MC will be OK BUT you will need to open it up and REMOVE the hat shaped check valve to use with your disc caliper, otherwise the brake pads/pistons will not retract properly because that valve holds residual pressure in the hydraulic system. It is for drum brakes only....
Harley Master Cylinder Kit.jpg
....RooDog....
You do not have the required permissions to view the files attached to this post.

DaCs
Posts: 93
Joined: Wed Sep 12, 2018 9:07 pm
Bikes: Panhead FL 1960
Location: Spain
Has thanked: 1 time
Been thanked: 2 times

Re: Panhead Rear disc brake

#3

Post by DaCs » Sun Nov 10, 2019 5:04 am

Thank you bro, you think its ok the GMA caliper or another option could be better?

RooDog
Site sponsor
Site sponsor
Posts: 954
Joined: Tue Oct 31, 2017 1:00 pm
Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Custom Built Evo 100" Bagger
Location: Knoxville, Tennessee
Has thanked: 217 times
Been thanked: 282 times

Re: Panhead Rear disc brake

#4

Post by RooDog » Sun Nov 10, 2019 5:25 am

I am running six GMA calipers on my two Harleys, están muy bien.
....RooDog,,,,,

DaCs
Posts: 93
Joined: Wed Sep 12, 2018 9:07 pm
Bikes: Panhead FL 1960
Location: Spain
Has thanked: 1 time
Been thanked: 2 times

Re: Panhead Rear disc brake

#5

Post by DaCs » Sun Nov 10, 2019 5:32 am

RooDog wrote:
Sun Nov 10, 2019 5:25 am
I am running six GMA calipers on my two Harleys, están muy bien.
....RooDog,,,,,
Ahuevo! vamos a probarlos entonces! Gracias

George Greer
Site sponsor
Site sponsor
Posts: 1494
Joined: Wed Mar 24, 2010 5:48 am
Bikes: 1942 WLA Type III
Hybrid WL/KH bobber project.
58 FL
Location: Markt Einersheim, Bavaria. and soon to be back in the US, Portland Oregon
Has thanked: 371 times
Been thanked: 78 times
Contact:

Re: Panhead Rear disc brake

#6

Post by George Greer » Sun Nov 10, 2019 4:07 pm

DaCs, pardon for the intrusion, this is a issue for me too.


RD,

So that little part could have been my issue with dragging banana brake!

But no matter now, I have replaced the rear brake, and looking for a original Lockheed Wagner M/C to replace the aftermarket one, and I will leave the part out.

George

RooDog
Site sponsor
Site sponsor
Posts: 954
Joined: Tue Oct 31, 2017 1:00 pm
Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Custom Built Evo 100" Bagger
Location: Knoxville, Tennessee
Has thanked: 217 times
Been thanked: 282 times

Re: Panhead Rear disc brake

#7

Post by RooDog » Sun Nov 10, 2019 5:54 pm

George....
Are you referring to the iron Wagoner, or the alloy Lockheed M/C? May I suggest either the original Harley 1980's vintage aluminum M/C that goes with your caliper, or a GMA M/C with a 5/8" bore. GMA lists them in both straight and staggered bolt pattern.
....RooDog....

George Greer
Site sponsor
Site sponsor
Posts: 1494
Joined: Wed Mar 24, 2010 5:48 am
Bikes: 1942 WLA Type III
Hybrid WL/KH bobber project.
58 FL
Location: Markt Einersheim, Bavaria. and soon to be back in the US, Portland Oregon
Has thanked: 371 times
Been thanked: 78 times
Contact:

Re: Panhead Rear disc brake

#8

Post by George Greer » Sun Nov 10, 2019 6:01 pm

Aftermarket.....and I am on the lookout for a original L-W m/c to replace the aftermarket one. Looks like I have the same repo kit...Exactly like the one in the above photo.

Except I am now using a Harley rear 2 piston brake caliper and bracket.

George

RooDog
Site sponsor
Site sponsor
Posts: 954
Joined: Tue Oct 31, 2017 1:00 pm
Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Custom Built Evo 100" Bagger
Location: Knoxville, Tennessee
Has thanked: 217 times
Been thanked: 282 times

Re: Panhead Rear disc brake

#9

Post by RooDog » Sun Nov 10, 2019 6:19 pm

The OEM version of that master cylinder is made of cast iron and is marked "WAGONER" on the side. It is 3/4" bore,and worked with the banana calipers, but then Harley went with an alloy M/C post banana. ....

I don't think Harley associated the name Lockheed with Wagoner.

The later alloy M/Cs used by Harley were Kelsey-Hayes brand. V-Twin lists their KH style M/C in both 5/8 and 3/4 bore sizes.

awander
Site sponsor
Site sponsor
Posts: 1331
Joined: Fri Sep 21, 2007 3:03 am
Bikes: '52 FL
'64 FLH
Has thanked: 24 times
Been thanked: 99 times

Re: Panhead Rear disc brake

#10

Post by awander » Sun Nov 10, 2019 6:32 pm

Hey, guys:

It's "Wagner", not "Wagoner".

And at least some of the master cylinders say "WAGNER LOCKHEED", in two lines, on them.

RooDog
Site sponsor
Site sponsor
Posts: 954
Joined: Tue Oct 31, 2017 1:00 pm
Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Custom Built Evo 100" Bagger
Location: Knoxville, Tennessee
Has thanked: 217 times
Been thanked: 282 times

Re: Panhead Rear disc brake

#11

Post by RooDog » Sun Nov 10, 2019 7:45 pm

Lo siento, Porter would have been proud.
And other that semantics, was I in error?

DaCs
Posts: 93
Joined: Wed Sep 12, 2018 9:07 pm
Bikes: Panhead FL 1960
Location: Spain
Has thanked: 1 time
Been thanked: 2 times

Re: Panhead Rear disc brake

#12

Post by DaCs » Sun Nov 10, 2019 9:13 pm

From what I understood here, my master cylinder is 5/8 and perfectly compatible with that GMA brake?

Regards

RooDog
Site sponsor
Site sponsor
Posts: 954
Joined: Tue Oct 31, 2017 1:00 pm
Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Custom Built Evo 100" Bagger
Location: Knoxville, Tennessee
Has thanked: 217 times
Been thanked: 282 times

Re: Panhead Rear disc brake

#13

Post by RooDog » Sun Nov 10, 2019 9:22 pm

3/4 or 5/8 will work just fine, I have used both, the 5/8 just gives more line pressure with less pedal effort, but it is basically unnoticeable unless you were to do back to back tests. I was a hustler and a trader, so I just kept changing out parts until I found something I liked, and then I stayed with it,,,,
....RooDog....

Post Reply

Return to “Panhead”