Knowledge Base: Motor: Top End (cylinders and heads)

General
Brakes
Carburetor and Fuel System
Chassis, Frame and Tires
Exhaust System
Electrical System
Forks

Ignition
Motor
Transmission and Clutch
Accessories
Documentation

Knowledge Base

Forum

Back to the Forum

Specific Motor categories:
Top End (cylinders and heads)
Bottom End (cases and crankshaft)
Gear Case (cams, idlers, cam cover)
Lubrication System (oil feed pump and scavenger pump, reservoir, filter, and lines)

Top End (cylinders and heads) (141)

1950 panhead tappet adjustment

1952 pushrods installation

1955 Cylinder Heads

1960 rear jug smoking

1964 Head rebuild

1965 cylinder oiling

1965 heads markings

Adjusting hydraulic lifters units on the Panhead

Adjusting solid lifters

Aftermarket Cylinder Kits

Aftermarket cylinders

Aftermarket heads

Base gasket alert

Base gasket leak

Base nuts torque specifications

Best hydraulic lifter

Bigger bore on early Pan

Blowing head gaskets on 1959 Pan

Chevy valves in pan

Circled F motor bolts for Pan rest

Collapsing lifters or weak oil pump

Converting from hydraulic to solid lifters

Cylinder base leak

Cylinder casting numbers and letter

Cylinder cutting out

Cylinder head bolts

Cylinder head broken exhaust port/spigot

Cylinder head coding

Cylinder head identification

Cylinder removal

Cylinder removal

Damaged exhaust port repair

Early pan hydraulic pushrods

Exhaust port tricks

Exhaust valve seat came out completely

Front head noise

Head bolt torque

Head restoration

Head/valves problems 1950 Panhead

Heads back from Head Hog

Hole in front piston

Hydraulic lifters

Hydraulic lifters seem to collapse

Intake Valve oilers - Missing

James fire ring head gaskets

Life expectancy of rocker arms/rocker bearings

Lifter question

Lifters: solid or hydraulic

New hydraulic lifters

Oil leaking from rearmost pushrod

One cylinder firing

Pan cover felt glue / Gorilla snot

Pan cover gaskets

Pan cover gaskets replacement

Pan head rocker blocks

Pan Shovel heads

Panhead front base gasket leak

Panhead head gaskets

Panhead valve oilers

Piston brand name

Piston specs (flathead)

Piston wrist pin reamers

Push Rods On Pan

Pushrod adjustment 1948 Panhead

Pushrod backed out

Pushrod cork change-out

Pushrod cover retainer installation

Pushrod lengths

Pushrods getting beat up

Pushrods: what should I use

Rear cylinder not running right

Rear cylinder removal

Rear cylinder running leaner than front cylinder

Replacing base/head/pan gaskets

Rocker arm bearings

Rocker arms aftermarket source

Rocker arms and bases

Rocker assembly end play

Rocker covers that eat gaskets

Rockerbox tin (cakepans)

Roller tip rocker arm

S&S stroker kits

Should I modify these jugs

Shovelhead & Panhead cylinders

solid lifter adjustment

Solid pushrod conversion

Some Observations about Solid Lifter Valve Adjustment

Split locknuts on solid lifters

Starting to smoke from the rear cylinder

STD exhaust configuration

STD heads and Shovel intake ports

STD heads info request

STD heads: a viable option?

STD heads: cam lift, duration and other specs Shovel specs

STD heads: lap valve seats

Strokin it........

Suggestions for removing paint from heads

Testing hydraulic lifters

The shrinking inch (rocker assemblies onto new STD heads)

Tips on changing engine oil

Top dead centre

Top end clatter!

Torque speck for rockers

Torqueing cylinder base nuts

V-Twin Stainless Rocker Covers

Valve adjustment on 1949

Valve clearance with solid lifters

Valve Collars Stricking Rocker Covers.

Valve cover interference with pads

VelvaTouch lifter kits

Copyright© 2010 Panhead/PTH