General
Identification
Brakes
Carburetor and Fuel System
Chassis, Frame and Tires
Exhaust System
Electrical System
 Forks
Ignition
Motor
Transmission and Clutch
Accessories
Library

Knowledge Base

Panhead & Flathead Knowledge Base
(Forum Archive)
Forum
Back to the Forum
Specific Motor categories:
Top End (cylinders and heads)
Bottom End (cases and crankshaft)
Gear Case (cams, idlers, cam cover)
Lubrication System (oil feed pump and scavenger pump, reservoir, filter, and lines)

Bottom End (cases and crankshaft) (118)
'54 crankcase rollers
1951 pan engine case leak
1954 cam gear case & cover gasket
1954 left case no oil drain plug
1956 FL tappet screen missing
1958-1962 right case
1959 breather gear
1962 Panhead cases..
1963 FL front engine sprocket seal
1965 crankcase vent
65 Tappet oil passage
Adjusting Crane hydraulic units
Aluminum in tappet screen
Another bloody oil leak
Bad case of cases
Blind case bolt hole has a crack
Bonneville brand cases
bottom end question
Breather Hose
Breather modification
Breather screen
Breather tube & belt drive
Can primary vent be plugged off ?
Case exploded! This can't be good
Case finish after welding
Case mating
Case numbers
Case Oil Screen bit me
case sealant
Case sealer
Cases
Cases Installation
Cases question
Cases...to repair or not to repair
Connecting rods
CPC Engine Case
Cracked case repair
Cracked tappet guide
Crank case breather
Crank case markings
Crank Case Repair?
crank rollers
Crankcase breather pipe and belt primary
Crankcase breather pipe set-up
Crankcase breather redirect and belt drive
Crankcase breather seems to have too much blow-by
Crankcase not venting correctly
Crankcase stud
Crankcase vent
Crankcase Vent
Crankcase ventilation
crankshaft thrust washer clearance question.
Cryogenic treatment cases
Engine case seal
Engine gasket glue
Engine main seal
Engine Sprocket Seal
Final finish for heads and engine cases
Flywheel assembly
Flywheel assy, Balancing.
Flywheel timing marks
Flywheels
Flywheels, stock or lightweight?
INSPECTION hole broken (panhead)
Left side sprocket seal
Lifter question: solid of hydraulic
Main Seal Leak on 1961 Pan FLH
Matching the engine cases
Need to lower end work?
No flywheel marks
oil breather
oil leak at tappet block
Oil restrictor for 50FL bottom end?
Paint the inside of the cases
panhead bottom identification
Panhead Right Side Case Boss???
Pinion nut torque
Piston Boss Orientation
Piston broke
Piston wrist pin reamers
Problem with Lifter Blocks
Pros´n´cons hydraulic vs. solid tappets
Push rod end size question
Question about sprocket shafts
replacing engine seal
Rod End Shake - Too much?
Rod Play
roller to timkin conversion
S & S pistons
S&S Flywheels
Salvaging flywheels
seperator and screen
setting up the bottom end
shovel cases panheads amd no oil to the heads
Shovel left case mated to a pan right side case
sidecar front end Timken bearing question
sifton lifters
Sloppy connecting rods
snapped pinion shaft
Solid lifters to hydraulic
Splitting cases
Sprocket shaft bearing nut
STD cases: need help
Stock flywheels 1951 pan
Stripped timing hole
Tappet block screws loosening
tappet bore wear
Tappet diameter
The roller on a lifter grenaded on my way up to speed
Timed breather gear
Timing cover question
Timing hole plug
Timing inspection hole
Timing plug: take out with the motor running
V-TWIN REPLICA CASES
What is the crankcase breather separator/screen for?
Who does good engine case repairs?
Worn tappet blocks

  ^^top^^
Copyright© 2012 Panhead/PTH